What are the application scenarios for printed circuit board assembly products?
Multiple IPC methods are available for users to choose from in different application scenarios. What are the application scenarios for printed circuit board assembly products?
Printed circuit board assembly tools have been widely used in many fields, including test benches, assembly equipment, modular assembly equipment, automated production equipment, and so on. Due to changes in testing requirements, electronic products have increasingly high requirements for the physical properties of products, which has led to a wide variety of testing probes.
The structure has reliable sealing and mechanical structure, which facilitates effective on-site operation and avoids problems caused by damage.
● The testing equipment adopts standard 100 μ As a standard testing probe, the m probe can test the contact area of crystal cards.
It can test the contact distance between the tube and the wire, and can reliably prevent water and other parasitic phenomena.
Attention: If the probe cannot be opened, a wrench can be used to align it with the pipe wall for 3D analysis, and do not soak it in water.
Test conditions: The charging voltage of each pin in the range of 2-25M Ω is 12-24V, and the power is 670W;
Normal conditions: When the power supply voltage changes within the range of 0V~36V, the power supply is cut off and the power supply voltage remains within 1V~36V.
Operating system: Windows 7 or above operating system, ARM9 or above operating system.
Display screen: LED display, capable of illuminating up to 80 degrees, exceeding the set illumination by 100 degrees, and illuminating for 1 second to achieve full brightness.
Front panel P C429, rear panel: PPG/galvanometer, LCD display, external PC.
Internal storage segment: A built-in DRAM storage segment that can store up to 30 sets of data, with built-in RC oscillation and Flash.
P2 output mode: two 33V: 5V DC input channels (6V) and three sets of analog RS-232 lines (4 Mbps); P0 input, 3 sets of analog inputs.
Power on (default boost after full charge) (boost): single 3 sets of analog inputs, fully digital mode programmable: according to 16 digits.
Simulation settings: A good PS/Alt control circuit transfers signals between input signals and loads, compatible with TTL level analog signals.
Simulation setup: A motor control circuit designed for high side D/A converter/AC-DC power supply.
Attention: The output voltage during passive output cannot exceed 03V, with a maximum of 1500V.
Printed circuit board assembly tools have been widely used in many fields, including test benches, assembly equipment, modular assembly equipment, automated production equipment, and so on. Due to changes in testing requirements, electronic products have increasingly high requirements for the physical properties of products, which has led to a wide variety of testing probes.
The structure has reliable sealing and mechanical structure, which facilitates effective on-site operation and avoids problems caused by damage.
● The testing equipment adopts standard 100 μ As a standard testing probe, the m probe can test the contact area of crystal cards.
It can test the contact distance between the tube and the wire, and can reliably prevent water and other parasitic phenomena.
Attention: If the probe cannot be opened, a wrench can be used to align it with the pipe wall for 3D analysis, and do not soak it in water.
Test conditions: The charging voltage of each pin in the range of 2-25M Ω is 12-24V, and the power is 670W;
Normal conditions: When the power supply voltage changes within the range of 0V~36V, the power supply is cut off and the power supply voltage remains within 1V~36V.
Operating system: Windows 7 or above operating system, ARM9 or above operating system.
Display screen: LED display, capable of illuminating up to 80 degrees, exceeding the set illumination by 100 degrees, and illuminating for 1 second to achieve full brightness.
Front panel P C429, rear panel: PPG/galvanometer, LCD display, external PC.
Internal storage segment: A built-in DRAM storage segment that can store up to 30 sets of data, with built-in RC oscillation and Flash.
P2 output mode: two 33V: 5V DC input channels (6V) and three sets of analog RS-232 lines (4 Mbps); P0 input, 3 sets of analog inputs.
Power on (default boost after full charge) (boost): single 3 sets of analog inputs, fully digital mode programmable: according to 16 digits.
Simulation settings: A good PS/Alt control circuit transfers signals between input signals and loads, compatible with TTL level analog signals.
Simulation setup: A motor control circuit designed for high side D/A converter/AC-DC power supply.
Attention: The output voltage during passive output cannot exceed 03V, with a maximum of 1500V
RELATED NEWS
PCB Manufacturing and Assembly in China
Contact Us
pcb board manufacturing How To Contact US
PCB from 1 to 30 layers, HDI, Heavy Copper, Rigid-flex board with "pcb board manufacturing One-Stop" service.